Part Number

Description

Unit of Measure

CG3-AB160Air BlockerPack of 2


​​■ IEEE 1101.10 compliant, 4HP wide
■ Material : Polycarbonate, PC GF20, UL94V-0

■ For 0.062" to 0.100" thick cards

■ For 80mm RTM (Rear Transition Module)

■ Screw-in mount

■ Comes with self tapping screw for attachment to horizontal extrusion rails
■ Available in Grey color only

Card Guides, Keyable, 4HP, IEEE 1101.10

Downloads  |

■ IEEE 1101.10 compliant, 4HP wide
■ Material : Polycarbonate, PC GF20, UL94V-0
■ For 0.062" to 0.100" thick cards
■ Available for 160mm and 220mm depth Eurocard
■ Snap-in mount
■ Available in Grey and Red color

Part Number

Description

Unit of Measure

CG3-K01/25Grey keysPack of 25
CG3-K02/25
Red keysPack of 25


​​​​■ ​Material : Polycarbonate UL 94-V0, Color : Blue
■ To conceal unused slots and prevent airflow.

■ Snap-fit onto keyable card guides in unused slots.

■ Suitable for all 4HP x 160MM standard guide rails (not offset).
■ This card retainer does not fit with EMC Rugged Subracks (CCA60 thru           CCA95) and extrusion rails (1440-0131, 1440-0132)


 80mm, Injection Molded for RTM

■ Material : Polycarbonate, PC GF20, UL94V-0

■ Keys are used for keying plug-in assemblies such as front panels and prevents them from being used in incorrect slots.

   These keys are installed in front chambers of CG3 series card guides and matched with an offsetting key inserted into

   type IV injector/ejector handles. By keying upper and lower card guides, over 4000 cobinations are possible.
■ Snap-in mount to square chambers of card guide/handle click on image to enlarge detail
■ Available in Grey and Red color

 160mm, 220mm, Injection Molded

Part Number

Description

Unit of Measure

CG3-160/12160mm Injection Molded, GreyPack of 12
CG3-160E/12
160mm Injection Molded with ESD clips, GreyPack of 12
CG3-220/12220mm Injection Molded, GeryPack of 12
CG3-220E/12220mm Injection Molded with ESD clips, GreyPack of 12
CG3-160R160mm Control Slot, RedPair


​​​​■ ​Material : Stainless Steel
■ ESD (Electrostatic Discharge) clips for CG3 series card guides provides

   permanent electrostatic discharge of the PCB before and after mate

   with connector
■ Snap-in mount to either end of CG3 card guides

​​■ IEEE 1101.10 compliant, 4HP wide
■ 3-Pieces Assembly

■ End Pieces Material : Polycarbonate, Grey

​■ Center Bridge Material : Aluminum Extrusion
■ For 0.062" to 0.100" thick cards
■ Snap-in mount
■ Available for over 220mm and custom length Eurocard

Part Number

Description

Unit of Measure

CG3-ESD/12PCB ESD clipPack of 12


 Coding keys for CG3-Series Keyable Card Guides

​​​​​■ IEEE 1101.10 compliant, 4HP wide
■ Material : Polycarbonate, PC GF20, UL94V-0

■ 0.5HP (0.100") offset

■ For 0.062" to 0.100" thick cards

■ Snap-in mount

■ Available in Green color only

 160mm, 0.5HP (0.100") offset, for Plug-in Power Supplies

 Over 220mm and custom lengths

Part Number

Description

Unit of Measure

CG3-280U/12280mmPack of 12
CG3-340U/12
340mmPack of 12
CG3-400U/12400mmPack of 12


Part Number

Description

Unit of Measure

CG3-80/1280mm for rear I/O, 6-pair of top/bottomPack of 12
CG3-80E/12
80mm with ESD Clips, 6-pair of top/bottomPack of 12


 PCB ESD clip for card guides

Part Number

Description

Unit of Measure

CG3-160G160mm power supply guidePair


 Air Block panel for Unused Slots

Keyable Card guides for EMC Subrack